Juniper-networks SRX 210 Manuel d'utilisateur Page 167
- Page / 176
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
NOTE: If contacting JTAC by telephone, enter your 11-digit case number
followed by the pound (#) key if this is an existing case, or press the star
(*) key to be routed to the next available support engineer.
Related
Documentation
Return Procedure for the SRX210 Services Gateway on page 147•
• Locating an SRX210 Services Gateway Component Serial Number and Agency Labels
on page 148
• Information You Might Need to Supply to Juniper Networks Technical Assistance Center
on page 150
• Packing the SRX210 Services Gateway and Components for Shipment on page 151
Packing the SRX210 Services Gateway and Components for Shipment
This topic includes the following sections:
•
Packing the Services Gateway on page 151
•
Packing the Components for Shipment on page 152
Packing the Services Gateway
To pack the services gateway for shipment:
1. Retrieve the shipping carton and packing materials in which the device was originally
shipped. If you do not have these materials, contact your Juniper Networks
representative about approved packaging materials.
2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect
the strap to the ESD point on the chassis or to an outside ESD point if the device is
disconnected from earth ground.
3. On the console or other management device connected to the services gateway, enter
CLI operational mode and issue the following command to shut down the services
gateway software:
user@host> request system power-off
Wait until a message appears on the console confirming that the operating system
has halted.
4. Shut down power to the device by pressing the Power button on the front panel of
the device.
5. Disconnect power from the device.
6. Remove the cables that connect to all external devices.
7. Remove all field-replaceable units (FRUs) from the device.
8. If the device is installed on a wall or rack, have one person support the weight of the
device while another person unscrews and removes the mounting screws.
151Copyright © 2013, Juniper Networks, Inc.
Appendix D: Contacting Customer Support and Returning the SRX210 Services Gateway Hardware
- SRX210 Services Gateway 1
- END USER LICENSE AGREEMENT 2
- Table of Contents 5
- Part 4 Appendixes 8
- Part 5 Index 9
- About This Guide 11
- Table 1: Notice Icons 12
- Obtaining Documentation 13
- Documentation Feedback 14
- Requesting Technical Support 14
- CHAPTER 1 19
- Components and Specifications 23
- ValueSpecification 24
- Memory, and PoE Versions) 25
- ComponentNumber 26
- Interfaces (continued) 28
- SRX210 Services Gateway LEDs 29
- Front Panel LEDs 30
- LEDs (continued) 31
- Ethernet Port LEDs 31
- Table 10 on page 16 32
- Boot Devices 33
- Dual-Root Partitioning Scheme 33
- Air flow 35
- CAUTION: 37
- ATTENTION: 37
- CHAPTER 3 39
- Introduction 39
- Supported Modem Types 39
- Services Gateway 40
- Using the 3G ExpressCard 40
- Key Features 40
- Physical Specifications 41
- CommandAction 43
- CDMA ExpressCards 43
- Commands (continued) 44
- Ethernet Support 45
- PoE Classes and Power Ratings 46
- Gateway (continued) 47
- Interface Modules 49
- Gateway Installation 53
- Installation (continued) 54
- Requirements 56
- Requirement for Clearance 58
- Recommended 58
- ClearanceLocation 58
- Documentation 59
- CHAPTER 8 63
- CHAPTER 9 65
- QuantityComponent 66
- QuantityPart 67
- Installation 69
- Rack-Mount Installation 70
- Desk-Mount Installation 71
- Wall-Mount Installation 72
- CHAPTER 11 73
- 60-Watt Power Supply 74
- 150-Watt Power Supply 75
- Mounting Brackets 76
- Services Gateway in a Rack 77
- Power Supply Adapter Tray 77
- Vertical Stand 79
- Services Gateway on a Desk 79
- Services Gateway on a Wall 81
- CHAPTER 12 83
- Autoinstallation 91
- CHAPTER 14 93
- 192.168.1.1 and use DHCP to 94
- ValuePort Settings 96
- Gateway End 97
- CHAPTER 15 101
- J-Web Interface 107
- Start to 109
- Your ActionFunctionField 110
- Services Gateway Hardware 113
- Hardware Components 115
- Components (continued) 116
- CHAPTER 17 117
- Possible Causes and 119
- Corrective Actions 122
- Possible Cause and Corrective 124
- ActionMeaningLED Status 124
- Appendixes 127
- Information 129
- Qualified Personnel Warning 132
- ADSL 2/2+ A 135
- Class 1 Laser Product Warning 141
- Class 1 LED Product Warning 141
- Laser Beam Warning 142
- Warnings 143
- Jewelry Removal Warning 144
- Lightning Activity Warning 146
- Operating Temperature Warning 146
- Product Disposal Warning 147
- Korean Class B Warning 151
- SRX210 Services Gateway Power 155
- Guidelines, Requirements, and 155
- Specifications 155
- GuidelineSite Wiring Factor 156
- 1.5 A maximum 157
- AC system current rating 157
- Grounding lug 158
- APPENDIX C 159
- Port (10/100 Mbps) 160
- Port (1 Gbps) 160
- Port (1 Gbps) (continued) 161
- Hardware 163
- Power Supply 0 165
- Contacting Customer Support 166
- Packing the Services Gateway 167
- Index on page 155 169
Produits connexes et manuels pour Matériel Juniper-networks SRX 210
(205 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels