Juniper-networks Juniper M-series M10i Manuel d'utilisateur

M10i Internet RouterPIC GuideJuniper Networks, Inc.1194 North Mathilda AvenueSunnyvale, California 94089USA408-745-2000www.juniper.netPart Number: 530

10 ft (3.05 m) posilock SMB to BNC (provided) Four pairs of Rx and Tx coaxial cablesCables and connectorsOne tricolor per port: Off—Not enabled Green

ATM2 E3 IQ PIC JUNOS 6.1 and laterSoftware release Two E3 ports Power requirement: 0.41 A @ 48 V (20 W) Intelligent queuing (IQ) PICs support fine-gra

One tricolor per port: Off—Not enabled Green—Online with no alarms or failures Amber—Online with alarms for remote failures Red—Active with a local al

ATM2 OC3/STM1 IQ PIC JUNOS 6.1 and laterSoftware release Two OC3 ports Power requirement: 0.41 A @ 48 V (20 W) Intelligent queuing (IQ) PICs support f

Circuit cross-connect (CCC) for leveraging ATM access networks User-configurable virtual circuit (VC) and virtual path (VP) support Support for idle

Table 3: Optical Interface Support for ATM2 OC3 IQ PICs (continued)MultimodeIntermediate Reach (IR)ParameterMultivendor agreementTelcordia GR-253Stand

ATM2 OC12/STM4 IQ PIC JUNOS 6.1 and laterSoftware release One OC12 port Power requirement: 0.41 A @ 48 V (20 W) Intelligent queuing (IQ) PICs support

Duplex SC/PC connector (Rx and Tx) Optical interface support—See Table 4 on page 17Cables and connectorsOne tricolor per port: Off—Not enabled Green—

Channelized DS3 IQ PIC JUNOS 6.1 and laterSoftware release Four DS3 ports Power requirement: 0.32 A @ 48 V (15.6 W) Intelligent queuing (IQ) PICs supp

One tricolor per port: Off—Not enabled Green—Online with no alarms or failures Amber—Online with alarms for remote failures Red—Active with a local al

This guide provides an overview and description of the Physical Interface Cards (PICs)supported by the Juniper Networks M10i Internet router. The PICs

Channelized E1 IQ PIC JUNOS 6.1 and laterSoftware release Ten E1 ports Power requirement: 0.15 A @ 48 V (7.2 W) Intelligent queuing (IQ) PICs support

Alarm indication signal (AIS) Loss of frame (LOF) Out of frame (OOF) Failed signal rate (FSR)Alarms, errors, andevents Layer 2 per-queue and per-chan

Channelized OC12 PIC JUNOS 6.1 and laterSoftware release One OC12 port Power requirement: 0.23 A @ 48 V (10.8 W) 12 DS3 channels Supports IP version 4

Alarm indication signal (AIS-L, AIS-P) BERT functionality (you can configure one DS3 channel in BERT mode and configure theremaining channels to tran

Channelized OC12 IQ PIC JUNOS 6.1 and laterSoftware release One OC12 port Power requirement: 0.23 A @ 48 V (10.8 W) Intelligent queuing (IQ) PICs supp

One tricolor per port: Off—Not enabled Green—Online with no alarms or failures Amber—Online with alarms for remote failures Red—Active with a local al

Channelized OC3 IQ PIC JUNOS 7.6 and laterSoftware release One OC3 port Power requirement: 0.39 A @ 48 V (18.6 W) Intelligent queuing (IQ) PICs suppor

One tricolor per port: Off—Not enabled Green—Online with no alarms or failures Amber—Online with alarms for remote failures Red—Active with a local al

Channelized STM1 IQ PIC JUNOS 6.1 and laterSoftware release One STM1 port Power requirement: 0.39 A @ 48 V (18.6 W) Intelligent queuing (IQ) PICs supp

Alarm indication signal (AIS-L, AIS-P) Bit error rate signal degrade (BERR-SD), bit error rate signal fail (BERR-SF) Bit interleaved parity errors B1

Table 1: PICs Supported in the M10i Internet RouterPagePICSlots RequiredFirst JUNOSSupportPortsPIC Family and TypeATM2 IQ91 slot6.14ATM2 DS3 IQ111 slo

Channelized T1 IQ PIC JUNOS 7.4 and laterSoftware release Ten T1 ports Power requirement: 0.15 A @ 48 V (7.2 W) Intelligent queuing (IQ) PICs support

Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection(RED), weighted random early detection (WRED) SNMP: T1 MIB an

DS3 PIC JUNOS 6.1 and laterSoftware release Two or four DS3 ports Power requirement: 0.47 A @ 48 V (22.5 W) Integrated DSU interoperability with leadi

One tricolor per port: Off—Not enabled Green—Online with no alarms or failures Amber—Online with alarms for remote failures Red—Active with a local al

E1 PIC JUNOS 6.1 and laterSoftware release Four E1 or coaxial ports Power requirement: 0.08 A @ 48 V (3.74 W) Two versions: 4-port, 120-ohm, RJ-48 4-p

One tricolor per port: Off—Not enabled Green—Online with no alarms or failures Amber—Online with alarms for remote failures Red—Active with a local al

E3 PIC JUNOS 6.0 and laterSoftware release Two E3 ports Power requirement: 0.47 A @ 48 V (22.5 W) Integrated DSU interoperabilityDescription High-dens

Alarm indication signal (AIS) Equipment failure (does not affect service) Frame error Line code violation Loss of signal (LOS) Out of frame (OOF) Yel

E3 IQ PIC JUNOS 6.1 and laterSoftware release Four E3 ports Power requirement: 0.38 A @ 48 V (18 W) Intelligent queuing (IQ) PICs support fine-grained

One tricolor per port: Off—Not enabled Green—Online with no alarms or failures Amber—Online with alarms for remote failures Red—Active with a local al

Table 1: PICs Supported in the M10i Internet Router (continued)PagePICSlots RequiredFirst JUNOSSupportPortsPIC Family and TypeEthernet IQ2511 slot7.6R

EIA-530 PIC JUNOS 6.1 and laterSoftware release Two EIA-530, X.21 or V.35 serial ports Power requirement: 0.07 A @ 48 V (3.4 W)Description Configured

Three bicolor per port: Data set ready (DSR): Green—DSR is detected or ignored Red—DSR expected but not present Data carrier detect (DCD): Green—DCD i

ES PIC JUNOS 6.1 and laterSoftware release High-bandwidth encryption (in accordance with IPSec standards) Power requirement: 0.21 A @ 48 V (10 W) Supp

Input and output bytes per tunnel Total authentication failures Total antireply failures Total encryption ASIC errors per PICInstrumentation(counters

Fast Ethernet PICsLeft: 4-Port Fast Ethernet PIC; Right: 8-Port Fast Ethernet PICLeft: 12-Port Fast Ethernet PIC; Right: VHDCI to RJ-21 cable JUNOS 6.

4-port PIC: Connector: Two-pair, Category 5 unshielded twisted-pair connectivity through an RJ-45connector Pinout: MDI noncrossover8-port PIC: Connect

Table 8: Optical Interface Support for Fast Ethernet PICs (continued)FX interface for 8-PortOptical Parameters62.5/125 micrometer MMF: 1.24 miles /2 k

Gigabit Ethernet PIC with SFP JUNOS 6.3 and laterSoftware release One Gigabit Ethernet port Power requirement: 0.15 A @ 48 V (7.3 W) Supports large Et

Status LED, one bicolor: Off—PIC is not enabled Green—PIC is operating normally Red—PIC has an error or failurePort LEDs, one pair per port: Link—If g

Gigabit Ethernet IQ PIC with SFP JUNOS 6.1 and laterSoftware release One Gigabit Ethernet port Power requirement: 0.46 A @ 48 V (22 W) Intelligent que

Adaptive Services II PIC JUNOS 6.4 and laterSoftware release Supports tunnel services. This feature is included with the PIC and does not require anin

Status LEDs, one tricolor: Off—Not enabled Green—Online with no alarms or failures Amber—Online with alarms for remote failures Red—Active with a loc

Gigabit Ethernet IQ2 PIC with SFP JUNOS 7.6R3 and laterSoftware release Four Gigabit Ethernet ports Power requirement: 0.65 A @ 48 V (31 W)Description

You can install any transceiver supported by the PIC. For information about installingand removing transceivers, see the PIC and Transceiver Installa

Table 11: Optical Interface Support for Gigabit Ethernet IQ2 PICs with SFP (continued)1000Base-LH1000Base-LX1000Base-SXParameter–3 through +3 dBm–11.5

Link Services PIC JUNOS 6.1 and laterSoftware release Power requirement: 0.17 A @ 48 V (8 W) Three versions: 4 multilink bundles, 256 LFI links 32 mul

MultiServices 100 PIC JUNOS 8.1 and laterSoftware release Supports tunnel services. This feature is included with the PIC and does not require anindiv

Table 12: MultiServices PICs Software Features Supported by the M10i Router (continued)8.1Stateful firewall with packet inspection: detects SYN attack

SONET/SDH OC3c/STM1 PIC JUNOS 6.1 and later (Type 1)NOTE: Although the illustration shows a multimode PIC, both a multimode PIC and asingle-mode inter

SONET alarms: Alarm indication signal—line (AIS-L) Alarm indication signal—path (AIS-P) Bit error rate signal degrade (BERR-SD) Bit error rate signal

Table 13: Optical Interface Support for SONET/SDH OC3c/STM1 PICs (continued)MultimodeIntermediate ReachParameterMultivendor agreementTelcordia GR-253S

Table 2: Adaptive Services PICs Software Features (continued)6.4Network Address Translation (NAT) for IP addresses6.4Port Address Translation (PAT) fo

SONET/SDH OC3c/STM1 PIC with SFP JUNOS 8.4 and laterSoftware release Two OC3c ports Power requirement: 0.25 A @ 48 V (12 W)Description Multiplexing an

SONET alarms: Alarm indication signal—line (AIS-L) Alarm indication signal—path (AIS-P) Bit error rate signal degrade (BERR-SD) Bit error rate signal

Table 14: Optical Interface Support for SONET/SDH OC3c/STM1 PICs with SFP (continued)Long Reach (LR-1)Intermediate Reach (IR-1)MultimodeParameterSFPSF

SONET/SDH OC3/STM1 (Multi-Rate) PIC with SFP JUNOS 8.4 and laterSoftware release Rate-selectable using one of the following rates: 1-port OC12 1-port

One tricolor per port: Off—Not enabled Green—Online with no alarms or failures Amber—Online with alarms for remote failures Red—Active with a local al

Table 15: Optical Interface Support for SONET/SDH OC3/STM1 (Multi-Rate) PICs with SFP Configured atan OC3/STM1 RateLong Reach (LR-1)Intermediate Reach

SONET/SDH OC12c/STM4 PIC JUNOS 6.1 and laterSoftware release One port Power requirement: 0.23 A @ 48 V (10.8 W)Description Multiplexing and demultiple

SONET alarms: Alarm indication signal—line (AIS-L) Alarm indication signal—path (AIS-P) Bit error rate signal degrade (BERR-SD) Bit error rate signal

Table 17: Optical Interface Support for SONET/SDH OC12c/STM4 PICs (continued)MultimodeIntermediate ReachParameterMultivendor agreementTelcordia GR-25

SONET/SDH OC12/STM4 (Multi-Rate) PIC with SFP JUNOS 8.4 and laterSoftware release Rate-selectable using one of the following rates: 1-port OC3 1-port

Adaptive Services II FIPS PIC JUNOS 7.2 and laterSoftware release JUNOS-FIPS requires an Adaptive Services II FIPS PIC for external IPSec connections.

One tricolor per port: Off—Not enabled Green—Online with no alarms or failures Amber—Online with alarms for remote failures Red—Active with a local al

Table 18: Optical Interface Support for SONET/SDH OC12/STM4 (Multi-Rate) PICs with SFP Configured atan OC3/STM1 RateLong Reach (LR-1)Intermediate Reac

SONET/SDH OC48c/STM16 PIC with SFP JUNOS 6.4 and laterSoftware release One OC48 port Power requirement: 0.86 A @ 48 V (41.4 W)Description Multiplexing

One tricolor per port: Off—Not enabled Green—Online with no alarms or failures Amber—Online with alarms for remote failures Red—Active with a local al

Table 20: Optical Interface Support for SONET/SDH OC48c/STM16 PICs with SFPLong Reach (LR)Intermediate Reach (IR)Short Reach (SR)ParameterSingle-mode;

T1 PIC JUNOS 6.1 and laterSoftware release Four T1 ports Power requirement: 0.08 A @ 48 V (3.7 W) Supports clear channel T1 per port (1.544 Mbps per c

Tunnel Services PIC JUNOS 6.1 and laterSoftware release Power requirement: 0.07 A @ 48 V (3.4 W)Description Loopback function that encapsulates and de

Appendix AHigh Availability FeaturesHigh availability features include Routing Engine redundancy, graceful Routing Engineswitchover (GRES), nonstop br

Copyright © 2008, Juniper Networks, Inc. All rights reserved.Juniper Networks, the Juniper Networks logo, NetScreen, and ScreenOS are registered trade

Status LED, one tricolor: Off—PIC is offline and it is safe to remove it from the chassis. Green—PIC is operating normally. Amber—PIC is initializing.

ATM2 DS3 IQ PIC JUNOS 6.1 and laterSoftware release Four DS3 ports Power requirement: 0.41 A @ 48 V (20.0 W) Intelligent queuing (IQ) PICs support fin